The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
They are making a few good annotation regarding Installing A Bathtub as a whole in this post on the next paragraphs.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Installing a bathtub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately hard task. If the old tub is readily easily accessible, the task can move immediately; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub and also set in the brand-new one. Make certain you have qualified yourself for the work and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to consider utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will certainly aid you install a brand-new bathtub in your shower room if you have already purchased a brand-new tub and don't need to change the setup of your previous water pipes.
Your tools as well as product checklist should consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the taps to drain any water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the restricted gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers are in place between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The former type must be linked to the tap ends first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Utilizing the two wooden boards under its feet, position the tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bath tub till the level checks out degree.
To mount faucets, fit the bottom of the outermost flexible tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the supply of water as well as examine all joints and brand-new pipework for leaks and also tighten them if required. Fill up the tub and also inspect the overflow outlet and also the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the tub must wait until the tub has actually been used a minimum of when as this will certainly resolve it right into its last position.
Planning for the Installation
First of all, the supporting framework supplied with the bath must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, causing the water to pass through the wall between the bath and also the tiling, bring about complications with wetness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can split rather very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I hope you liked our excerpt about A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read our post. Sharing is caring. Who knows, you may just be helping someone out. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Plumbing crisis? Reach out! Report this page